Regulation No 80 of the Economic Commission for Europe of the United Nations ... (42010X0630(02))
Regulation No 80 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of seats of large passenger vehicles and of these vehicles with regard to the strength of the seats and their anchorages
- Regulation No 80 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of seats of large passenger vehicles and of these vehicles with regard to the strength of the seats and their anchorages
- 1. SCOPE
- 2. DEFINITIONS
- 3. APPLICATION FOR APPROVAL
- 4. APPROVAL
- 5. REQUIREMENTS FOR SEATS
- 6. REQUIREMENTS FOR SEAT ANCHORAGES OF A VEHICLE TYPE
- 7. REQUIREMENTS FOR INSTALLATION OF SEATS IN A VEHICLE TYPE
- 8. CONFORMITY OF PRODUCTION
- 9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 10. MODIFICATION AND EXTENSION OF APPROVAL OF THE SEAT TYPE AND/OR THE VEHICLE TYPE
- 11. PRODUCTION DEFINITELY DISCONTINUED
- 12. TRANSITIONAL PROVISIONS
- 13. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- Appendix 1
- 1. Requirements
- 2. Preparation of the seat to be tested
- 3. Dynamic tests
- 3.1. Test 1
- 3.2. Auxiliary seat
- 3.3. Manikin
- 3.4. Impact simulation
- 3.5. Test 2
- Figure 1
- Appendix 2
- Test procedure for the anchorages of a vehicle in application of paragraph 6.1.1
- 1. Test apparatus
- 2. Test procedure
- Appendix 3
- MEASUREMENTS TO BE MADE
- 2.1. Measurements to be made on the trolley
- 2.2. Measurements to be made on manikins
- Appendix 4
- DETERMINATION OF ACCEPTABILITY CRITERIA
- 1. Head acceptability criterion (HAC)
- 2. Thorax acceptability criterion (ThAC)
- 3. Femur acceptability criterion (FAC)
- Appendix 5
- STATIC TEST REQUIREMENTS AND PROCEDURE
- 1. Requirements
- 2. Static tests
- 2.1. Test apparatus
- 2.2. Test procedure
- Figure 1
- Static test apparatus
- Appendix 6
- Energy absorption characteristics of the rear part of seat backs
- ANNEX 1
- COMMUNICATION
- (maximum format: A4 (210 × 297 mm))
- ANNEX 2
- COMMUNICATION
- (maximum format: A4 (210 × 297 mm))
- ANNEX 3
- ARRANGEMENTS OF APPROVAL MARKS
- 1. Arrangement in the approval mark for a seat
- 2. Arrangement of the approval mark for a vehicle type
- ANNEX 4
- Procedure for determining the ‘H’ point and the actualtorso angle for seating position in motor vehicles
- 1. PURPOSE
- 2. DEFINITIONS
- 3. REQUIREMENTS
- 3.1. Data presentation
- 3.2. Relationship between measured data and design specifications
- 4. PROCEDURE FOR ‘H’ POINT AND ACTUAL TORSO ANGLE DETERMINATION
- 4.7.1. Designated seating position: driver and outside front passenger
- 4.7.2. Designated seating position: outboard rear
- 4.7.3. Other designated seating positions:
- Appendix 1
- Description of the three dimensional ‘H’ point machine
- (1)
- (3 DH machine)
- 1. Back and seat pans
- 2. Body and leg elements
- Figure 1
- 3 DH machine elements designation
- Figure 2
- Dimensions of the 3 HD machine elements and load distribution
- Appendix 2
- THREE-DIMENSIONAL REFERENCE SYSTEM
- Figure
- Three-dimensional reference system
- Appendix 3
- REFERENCE DATA CONCERNING SEATING POSITIONS
- 1. Coding of reference data
- 2. Description of vehicle measuring attitude
- 2.1. Co-ordinates of fiducial marks
- 3. List of reference data
- 3.1.1. Co-ordinates of ‘R’ point
- 3.1.3. Specifications for seat adjustment(1)
Feedback